ntc interchangeable type sc series thermometrics thermistors features ? precision, solid state temperature sensor ? epoxy flled sleeve for controlled diameter ? interchangeability down to 0.18f (0.10c) ? suitable for use over the range of -40f to 302f (C40c to 150c ? high sensitivity greater than C4%/c at 77f (25c) ? most popular resistance (r) vs temperature (t) curves are availablee ? suitable for temperature measurement , control and compensation ? ideal for medical applications ? fully insulated ? sleeved for good mechanical strength and resistance to solvents ? 0.008 in (0.2 mm) diameter heavy isomid insulated biflar copper lead wires for sc50 ? 0.004 in (0.1 mm) diameter heavy isomid insulated biflar nickel lead wires for sc30 a mphenol advanced sensors
type sc30 specifcations ntc interchangeable type sc30 sleeved interchangeable chip thermistors with heavy isomid insulated nickel lead-wires. options consult factory for availability of options ? other resistance values in the range of 1000 to 100 k ? other tolerances or ranges ? alternative lead wires or lengths ? non standard r vs t curves ? controlled dimensions thermal and electrical properties dissipation constant still air: 0.4 mw/c stirred oil: 3 mw/c thermal time constant still air: 5 seconds stirred oil: 0.3 seconds maximum power at 77f (25c) ~30 mw de-rated from 100% at 77f (25c) to 0% at 212f (100c) ordering information select appropriate part number below for resistance and temperature tolerance desired. r 25c material system 0.18f (0.1c) 32f to 158f (0c to 70c) 0.36f (0.2c) 32f to 158f (0c to 70c) 2252 f sc30f232v sc30f232w 3000 f sc30f302v sc30f302w 5000 f sc30f502v sc30f502w 10000 f sc30f103v sc30f103w 10000 y sc30y103v sc30y103w 30000 h sc30h303v sc30h303w 50000 g sc30g503v sc30y503w 100000 y sc30y104v sc30y104w 100000 g sc30g104v sc30g104w ntc interchangeable type sc30 dimensions epoxy fllet 38ga, nickel, alloy biflar leads ? 0.030 in (0.76 mm) maximum 1.5 in (38 mm) minimum length from 0.04 to 0.12 in (1 to 3 mm) depending on resistance of thermistor polyimide sleeve
type sc50 specifcations ntc interchangeable type sc50 sleeved interchangeable chip thermistors with heavy isomid insulated copper lead wires. options consult factory for availability of options. ? other resistance values in the range of 1000 to 100 k ? other tolerances or ranges ? alternative lead wires or lengths ? non standard r vs t curves ? controlled dimensions thermal and electrical properties dissipation constant still air: 0.5 mw/c stirred oil: 0.4 mw/c thermal time constant still air: 8 seconds stirred oil: 0.5 seconds maximum power at 77f (25c) ~50 mw de-rated from 100% at 77f (25c) to 0% at 212f (100c) ordering information select appropriate part number below for resistance and temperature tolerance desired. r 25c material system 0.18f (0.1c) 32f to 158f (0c to 70c) 0.36f (0.2c) 32f to 158f (0c to 70c) 2252 f sc50f232v sc50f232w 3000 f sc50f302v sc50f302w 5000 f sc50f502v sc50f502w 10000 f sc50f103v sc50f103w 10000 y sc50y103v sc50y103w 30000 h sc50h303v sc50h303w 50000 g sc50g503v SC50Y503W 100000 y sc50y104v sc50y104w 100000 g sc50g104v sc50g104w ntc interchangeable type sc30 dimensions epoxy fllet 32ga, copper biflar leads ? 0.050 in (1.5 mm) maximum 1.5 in (38 mm) minimum length from 0.04 to 0.12 in (1 to 3 mm) depending on resistance of thermistor polyimide sleeve
aas-920-307c-03/2014 www.amphenol-sensors.com ? 2014 amphenol corporation. all rights reserved. specifcations are subject to change without notice. other company names and product names used in this document are the registered trademarks or trademarks of their respective owners. a mphenol advanced sensors
|
